- Views: 23
- Report Article
How to wear 3D Mink lashes
Posted: Sep 03, 2019
After buy many 3D Mink lashes, you will find eye type, eye length is not appropriate, therefore, when using 3D Mink lashes, firstly use tweezers to pick up the 3D Mink lashes at the root of the eyelashes, if the 3D Mink lashes longer than their own eyes You need to cut to the same width as your own eye shape, and the end of 3D Mink lashes should not overshoot their own eyelashes. Therefore, the 3D Mink lashes in the eyes should empty out of 1/4, or eyes closed will be uncomfortable.Second step: clip their own eyelashes
Before apply the 3D Mink lashes, use the eyelash curler curling up your eyelashes, and then mascara, because their own eyelashes is no more than 3D Mink lashes curling, in order to wear the natural eyelashes naturally, and therefore need to wear 3D Mink lashes prior to curling their own eyelash, while mascara is also able to help fix the curvature of the eyelashes.Third step: to give 3D Mink lashes wear glue
After their own eyelashes are fixed, pick up the prepared 3D Mink lashes, roots up, and then use another hand squeeze the glue on the 3D Mink lashes, should pay attention when crowded squeeze extrusion not too much one-time Or it will flow the eyelash glue onto the eyelashes. When applying the eyelash glue, it should be applied to both sides from the middle so that the eye and eye end parts will have more glue because the two parts are easier to fall off. Better grasp of the coating method is to squeeze a little glue, painted a short, squeeze a little glue, painted a short, so until all painted, the direction is just said from the middle to both sides.Fourth step: How much eyelash glue is the right
Many people wear 3D Mink lashes, the biggest difficulty is that do not know how much glue to the 3D Mink lashes wear, so editor answer, false eyelash glue is about 0.5 to 1 mm thickness, because if the 3D Mink lashes glue too little, Not good sticky 3D Mink lashes, squeezed in the eyelash glue, wait 30 seconds, to be 3D Mink lashes semi-dry state, because the viscosity is the highest.Fifth step: first time wear 3D Mink lashes
After the glue on the 3D Mink lashes is semi-dry, clamp the middle of the eyelashes with tweezers. At this moment, it is not the root of the middle of the 3D Mink lashes. Instead, the eyelashes in the middle of the 3D Mink lashes are clamped by the forceps, Just above the real eyelashes roots. The middle of the 3D Mink lashes align with the real eyelashes. Be careful not to touch the roots of the glue with real eyelashes.Sixth Step: How to wear the eye 3D Mink lashes one eye
First stick in the middle part, the site is above the real eyelashes within 0.5-1 mm. Is glued to the eyelids, very close to the real eyelashes, but do not press on the real eyelashes line because it will put down real eyelashes down.Seventh step: How to wear 3D Mink lashes one eye end
Stick eye tail part. Use tweezers to clamp the hair on the tail of the 3D Mink lashes and gently press the eyelashes on the end of the eye 0.5-1 mm in the direction of the end of the eye. The goal is to prevent the middle of the excess part of the empty bent out, but do not be too hard, the middle of the 3D Mink lashes should still just fixed position.
Eighth step: how to wear 3D Mink lashes on the eyelash head
Stick eyes head. This time with tweezers to clamp the hair of the head of 3D Mink lashes, gently pressed toward the head of the eye in the direction of the eyelash line 0.5mm above the eye (1mm will be too high, this should be closer to the real eyelashes Will naturally).
Ninth step: the final shape of?3D Mink lashes
After pasting 3D Mink lashes with the finger hold it until the glue is completely dry to amend the arc. Do not lift the eyelashes too high, this will be layered with real eyelashes. Do not squeeze too low, this will make the eyes look smaller. Probably held at their own height of 30 seconds, so that it will fix the height of curved eyelashes
Thanks for sharing this article.