A Detail Guide on How to Install Drywall by Painting Contractor Toronto

Drywall install is not complex. It requires the right guidance and necessary tools.

This drywall installation guide will help you with how to install drywall in the simplest way possible.

While Toronto Drywall Contractor takes years to perfect, the careful homeowner can try to install drywall.

Tools for Drywall Installation

Finishing a room with drywall requires a few essential tools for drywall and materials that can be purchased at a hardware store. The term "drywall" is the common term for gypsum board.

Gypsum board is available in sheets of 1.2 m by 2.4 m of various thicknesses.

The standard thickness is 1.5 cm, and should not be deviated from it unless the code dictates or for special design needs.

• An electric screwdriver

Although it is possible to use nails, an electric screwdriver is often faster to cover large areas. Use 2.8cm coarse thread sheet metal screws with the screwdriver.

• A putty knife

At a minimum, have a knife 6 to 8 inches wide to use for the putty. A wider blade, such as a 12-inch blade, is better than a narrower 12-inch blade.

• Joint sealant

Also known as sludge, the joint compound should be purchased premixed. Mix the compound lightly before use, but do not do it vigorously as you will introduce air bubbles into the mud.

• Drywall tape

Use regular tape, made of paper, with a slight seam in the center. Special tapes should only be used for special applications.

• Angles

For each outside corner, you will need a metal angle iron to protect the drywall.

• A sanding sponge

While some people prefer sandpaper, these sponges are easy to use for little touch-ups also as larger projects.

Preparing for Drywall

In most cases, homeowners hang drywall on studs that have already been covered with another material. To properly hang drywall, all this covering must be removed.

Fasteners, such as screws, nails, or staples, should also be removed from the studs. If the clips cannot be easily removed from the wall, they can be driven deeper into the stud until the clip is flush with the face of the stud.

While the studs are exposed, mark the floor and ceiling to note the location of each stud. This will make them easier to find when you are installing drywall.

How to install drywall

After the wall is prepared, installing drywall is a simple task.

• Use a few pieces of wood 1cm wide to hold the first piece of drywall off the floor. Always start with an inside corner, hanging the drywall horizontally.
• Cut it so that it ends in the center of a post. This will allow you to secure the ends of the two pieces to the upright.
• Check whether there are any electrical outlets or sockets that will be covered by the drywall. Cut rectangular openings for these fixtures before hanging.
• Screw into the drywall and the stud behind it, spacing the screws every 8 inches along each stud. Drive-in each screws so you can cover the head later.
• Continue to use this method to secure the rest of the partition, staggering the vertical joints as much as possible.

The plaster

The plaster is the most difficult part of working in drywall installation it may require a professional drywall installation expert in Toronto. It is difficult to hide your joints under layers of plaster and duct tape, especially if you want a smooth wall.

• Begin applying a thin coat of sealant to the bulkhead joint using a trowel. The coating should extend three inches on each side.
• Place the tape over the joint, trying to match its center with the joint as much as possible. Squeeze it into place with your hands, making sure there are no bubbles or creases.
• Apply a small amount of sealer to the drywall strip, creating a smooth coat over the joint.
• Use a clean knife to remove as much sealant as possible, without exposing the tape or creating bumps.
• Let the wall dry for at least 8 hours. During this time, you can fill the screw heads with a little filler on the edge of a knife.
• Lightly sand the dried plaster, removing any dents or streaks.
• Using a knife at least 8 inches wide, add a small amount of sealant to the joints to make them as smooth as possible.
• Let the fittings dry and lightly sand them.

Angles

Angles require special treatment. However, taking the time to finish and reinforce the angles can extend the life of the wall.

Inside corners

Fold the drywall strip in half, using the guideline printed in it. Add filler to the corner and press the drywall tape into place. Use the same techniques for finishing to finish the inside corner.

Outside corners

Cut the metal cord to cover the entire length of the corner. Screw it in place to cover the corner, every 8 inches. With a generous amount of filler on a filler knife, cover the corner. Let dry and sand any imperfections. Continue to apply coats of compound until the corner is covered.

The finishing touch

Even with careful plastering, a novice can still show drywall joints. In this case, a light texture can be applied to the entire wall to hide the joints using a joint compound.

If you don't want to have textured walls, it's important to practice in the hidden areas before you take on larger work.

Learning how to install drywall can be difficult and is not for everyone.

Homeowners who want texture-free and flawless walls will need to hire a professional Painting Contractor Toronto who has extensive experience in drywall installation.

Once the walls are in place, you can keep their original appearance by repairing any damage with a drywall repair kit.

Mas Construction House Painter in Toronto. We are a skilled and experienced team of Painters in Toronto. We are specialized in Exterior painting, Interior painting, Drywall installation, Venetian plaster, and Popcorn ceiling removal, and many more.