How To Prevent Laser Condensation In Summer?
Posted: Jun 10, 2021
In summer, it is very important to prevent laser condensation in an environment with high temperatures and humidity. When the laser cooling water temperature is set lower than the corresponding dew point temperature, condensation is likely to occur. Under normal circumstances, the influence of condensation on the laser has a gradual process. In the early stage of internal condensation, there will be some easy-to-find signs. For example, condensation will usually appear on the surface of the externally exposed cooling water pipe first, and then it will spread to the inside of the laser after a period of time. So how should we prevent the laser from condensation?
What is condensation?
Condensation refers to the phenomenon that when the water vapor in the air reaches a saturated state if the ambient temperature continues to drop, the supersaturated water vapor in the air condenses into water and precipitates out. Simply put, when we put an object under a certain temperature, humidity and pressure, gradually reduce its temperature, when the temperature of the object drops below the "dew point temperature" of the environment (that is, the temperature of the surrounding air), the object precipitates and "condenses" Water"), the surface of the object will deposit water and dew, which is condensation. For example, when you walk from an air-conditioned room with glasses to the outdoors in summer, your glasses are foggy, which is also a phenomenon of condensation.
The harm of condensation to the laserFor laser cavities, optical components, and some electronic modules of lasers that require water cooling, if they work in a high temperature and high humidity environment for a long time, condensation will appear on the surface of the object. This will increase the probability of failure of the electronic module immersed in water, and may also cause the lens to be contaminated by water mist and cannot be used or burned.
How to prevent laser condensation?
- Use dew point temperature checklist
The left side is the current working environment temperature, and the top side is the current working environment humidity. The intersection temperature of the temperature and humidity parameters is the "dew point temperature" in this environment. Therefore, the adjustment principles are as follows:
The low-temperature water should be adjusted within the range of 15-30?, and should not be lower than the dew point temperature of the environment inside the laser, and should be as close to 25? as possible.
Normal temperature water should be adjusted within the range of 5-30?, and should not be lower than the dew point temperature of the working environment of the laser head, and should be as close to the current ambient temperature as possible. Otherwise, the working environment needs to be improved according to the dew point temperature look-up table.
Note: If the temperature and humidity fluctuate greatly on the day of use, the dew point temperature must be calculated based on the maximum possible value of temperature and humidity, otherwise condensation may still occur and damage the laser and laser output head.
Lasers above 1500 watts must be equipped with an air-conditioned room. If the air conditioner is not installed, it is prohibited to turn on, otherwise, the laser will be 100% dew, and related failures caused by dew will not be covered by the warranty.
Since condensation is an objective physical phenomenon, it cannot be avoided 100%, but we still need to remind everyone that when using the laser: be sure to minimize the temperature difference between the laser’s operating environment and its cooling temperature.
- Water temperature setting
The cooling water temperature of the laser output head is 2?-3? higher than the ambient temperature.
- Anti-condensation boot operation
Start the supporting water cooler, wait for the water temperature to rise to the preset temperature, and the laser emits light.It is recommended that under the premise of ensuring safety, the laser should be powered off at night to keep the air conditioner in continuous operation or install the laser in an air-conditioned room.
- Anti-condensation shutdown operation
Turn off the water cooler after 5-10 minutes.
Turn off the air conditioner (total power) after 30 minutes.
- Air conditioning maintenance
- Ensure the enclosure is sealed
1. Check whether each cabinet door exists and is closed tightly;2. Whether the lifting bolts on the top are tightened;3. Whether the protective cover of the unused communication control interface at the rear of the chassis is covered, and whether the used ones are fixed.
The above points are some effective measures to prevent the risk of fiber laser condensation. If you encounter other problems while using the fiber laser cutting machine, you can leave us a message for consultation, and our technicians will reply to you as soon as possible. I hope it can help you.
My current work is related to the Cnc router machines. I am working at a company called Forsun Cnc, Forsun Cnc Router helps you stay productive. https://forsuncnc.com/