A guide to choosing the correct water pump based upon the house's construction

A guide to choosing the correct water pump based upon the house's construction. To enjoy a relaxing shower

Imagine going through every aspect you're planning for your bathroom. After you've chosen the bathroom design You can locate the perfect shower heads. One issue It's that you've overlooked the most essential element of bathroom design: pumping.

What's the purpose of Shower Pumps?

Shower pumps are used to increase the water pressure in pipes. They are utilized to expel the water, and also increase the strength of your shower system. If you own an electric heater, it increases the water volume in the initial storage unit. Due to the increased pressure of the water shower heads aren't dripping and give you the luxurious showering experience that you paid them to offer!

The pressure of the pump is measured in bars. A bar is 10 metric heads of water. Each shower must be at the pressure minimum specified in the description.

For example the stunning black shower head will require a minimum water pressure of 0.5 bars. It is suitable for low to medium pressure.

You can determine the pressure of the water by using a test gauge for a more precise measurement.

You can also test it yourself with an easy test. All you require is a single-litre container and a stopwatch. Before you start the test, ensure that all water outlets are shut. Follow these steps:

1. Start the timer.

2. The water vessel should be placed right in front of your shower head.

3. Once the vessel is filled Once the vessel is full, stop the timer. This is it.

If a 1-liter container takes more than 10 seconds to fill it could be an issue with water pressure. These tips will help you find the ideal water pump prior to rushing to purchase one.

Try to answer these three questions about your water pump prior to adding shower heads to the shopping cart.

1. What's it's Flow rate?

The performance of the water pump is not only determined by the pressure of its water, but also the flow rate. The flow rate is the number of litres per minute that can pump out at a certain pressure.

60 / (time) = (x) litres per minute.

You've observed that your one-litre water vessel takes 10 seconds to fill. The flow rate you get is 60/10=6 litres/hour.

A less expensive water pump may create 3 bars of water pressure, but the shower head won't function at the maximum if its flow rate is not enough.

1. Is it Single Impeller or Twin Impeller?

Single Impeller: Single shower pump or single impeller is designed to boost just one water supply type.It is mostly used to pump hot water and is generally recommended in the event of pumping problems using a single type of water supply.

Twin Impeller: Like the name implies, Twin Impellers can be used to boost both cold and hot water supply. They are able to boost hot and cold water flow as well as inject them into shower heads. They are the top-selling option due to their longevity.

1. Basic Pumping Structure for Your House

This is a vital aspect to know what the shower head needs. You don't have to check blueprints or call your pumping company yet. We promise you can do this yourself. It's easy.

Water pressure can also be affected by the location of your house. In the case of a home on the hills, or located in rural areas, the water pressure will be lower. However, the majority of the structures for pumping water to a house within the UK is easily separated into three different categories.

1. TraditionalGravity Fed

This is the most popular type of pumping system that is available in the UK. This is the best option for homes that have more than one bathroom. In a gravity-fed structure, the cold water tank will be located in the roof, attic or loft. Additionally, the hot water cylinder will be close to the bathroom. It is ideal for low-pressure housesand is able to work on the solar system. However, storage of the cold tank takes up a lot of space. Low pressure in the hot tank can cause quality problems and lead to rapid degradation.

If you've got a gravity-fed pumping arrangement the requirements for pumping may be further categorised into positive and negative head/universal head.

It is typically identified by the location of the cold tank up to the outlet point. It is possible to understand the distinction between them by knowing how they function. One pushes water into the shower head, while the other is pulling.

Positive Head Shower Pump

A shower head with a positive pressure is needed when the cold water tank is larger than the shower head. It is dependent on gravity to push the water from the cold storage unit to your outlet. The flow is then boosted by the impeller to pump water.

A minimum distance of 990mm is needed above the shower head so that the impeller can start the process.

Universal Head Shower, also known as Negative Head Pump

If your shower heads are above the same level as your cold water tank, you must use negative or universal head pumps for showers.

Instead of relying upon gravity shower heads are able to pressurize the entire pipe, from the water tank to mixer valve, in order to ensure that the system will automatically start.

They are suitable for flows of less than 600ml per minute.

1. Combi-boiler system

Combi Boilers combine a high-efficiency water heater with a central heating boiler to form one compact unit. It is able to draw water from the main supply, 'as per the requirement'. The typical system has one hot water cylinder, which is situated at the floor below the home and it is used to supply water to the rest of the home. They require less effort to set up and do not hold cold water in cold tanks as do gravity-fed systems. They are inexpensive and use less space. They're ideal for smaller houses and have no danger of the pipes freezing during the winter.

1. Unvented System

An Unvented Pumping System will typically provide hot water in an airing cupboard near the bathroom in the main. They can supply hot water to any number of taps within the mains pressure. They are simple to install and will cost less than the other hot water systems. They're highly dependent on the main cold water supply. This means that if there is no cold water supply, the hot water supply will be cut off.

Now, you can finally select which shower head that meets your requirements. At Taron We provide simple to install stylish shower heads that will add value to your budget and are compatible with your pump's water pressure. This chart will assist you in selecting the best choice for your bathroom.

We must bring up the General Guideline:

Low boost = Pressure up to 1.0 bar

Up to 2.0 bar pressure = medium boost

3.0 bar plus bar pressure = High boost

If you've realized that your pump is able to boost somewhere between 2.7 bar of pressure in the water this means that it's able to meet 2.5 to 3 bar pressure. At Tapron We think you deserve the top shower after a hard day at work and we have been persistent in delivering it by offering a wide variety of shower heads.

Water Pressure

Type of showerhead

It is perfect with

Minimum 0.5 bar

Matt Black Overhead Shower 200mm

HTML0 Solex Black Thermostatic Concealed 3 Outlet Shower Valve

Minimum 1.0 bar

Victorian Shower Head

Brushed Gold 3 Outlet Concealed Thermostatic Shower Valve

Minimum 1.0 bar

Slider Rail With Multi-Function Shower Head

Florentine Concealed Manual Valve

Let us know which Tapron product is your absolute favorite this season. We'd be delighted to hear from you.

Chat with us about any queries or to receive assistance.