Frigidaire Washer Not Draining: Here Are The Quick Fixes

A Frigidaire washer that isn't draining properly can be a major inconvenience. If your clothes are left soaking wet after a cycle, it’s likely due to an issue with one or more of the key Frigidaire washer parts. In this article, we'll cover the most common causes of drainage issues and provide easy, step-by-step fixes to help restore your washer's performance. With a little troubleshooting and regular maintenance, you can keep your washer running smoothly for years to come.

Common Reasons for a Frigidaire Washer Not Draining and Quick Fixes

Here’s a breakdown of the typical causes of drainage issues in Frigidaire washers and step-by-step fixes to resolve them:

1. Clogged or Blocked Drain Pump Filter

Over time, small debris such as lint, coins, buttons, and even fabric fibers can pile up inside the washer’s drain pump filter and hamper water flow.

Quick Fix:

• Locate the Filter: Find the drain pump filter, usually at the bottom front of the washer behind a small panel, and refer to your washer’s manual.

• Clean the Filter: If you place a towel or tray under the panel, you can catch any water. Take it out, clean it under running water, and put it back.

• Regular Maintenance: You need to clean the filter every 1-2 months to prevent future blockages.

2. Kinked or Obstructed Drain Hose

Water pumped out of the washer is channeled by the drain hose. Water won’t drain well if it’s kinked, clogged, or improperly installed.

Quick Fix:

• Inspect the Hose: Check for any obstructions, kinks, or bends in the hose.

• Clear Blockages: Remove clogs from the hose by detaching it from the washer and flushing it with water.

• Reposition the Hose: Make sure it’s installed correctly with no sharp bends and is at the correct height not to siphon.

3. Faulty Lid Switch or Door Lock

In the top load washer, if the lid switch or in the front load washer, the door lock malfunctions washer may stop mid-cycle and refuse to drain.

Quick Fix:

• Test the Switch: When you close the door or lid, you should hear a clicking sound. If the switch doesn't click, it can be broken.

• Replace the Switch: Call a technician or replace the faulty switch with the equivalent piece for your product.

4. Malfunctioning Drain Pump

The heart of the washer’s drainage system is the drain pump. If the drum is broken or blocked, water won't flow out of it.

Quick Fix:

• Check for Blockages: Shut off the washer, unplug the washer, and look for debris in the pump.

• Test the Pump Motor: Check for continuity with a multimeter. Replace the pump if it’s defective.

• Professional Help: Hire a specialist if you are unsure how to manage pump repairs.

5. Detergent Buildup

The drainage system of the washer may become clogged with soap scum if you use too much detergent.

Quick Fix:

• Use the Right Detergent: For your Frigidaire washer always use HE (High Efficiency) detergent.

• Start a Cleaning Cycle: If a buildup is present, remove it with a washer cleanser or a vinegar and baking soda solution.

• Moderate Detergent Usage: Since one of the key steps in preventing excess residue is measuring detergent according to load size and soil level, it is recommended to stick to a measured and sensical detergent dose.

6. Faulty Water Level Pressure Switch

The water level in the drum is sensed by this switch. The washer may not drain if it’s faulty — it won’t signal the drain pump to work properly.

Quick Fix:

• Inspect the Switch and Hose: Look at the hose connected to the switch to see if it is blocked or damaged.

• To fix a broken switch, swap it out for a new one that fits the model of your washer.

7. Drainage System Installation Issues

Siphoning, backflow, or slow drainage can occur if the drain hose or drainage system is improperly installed.

Quick Fix:

• Verify Installation: Make sure the drain hose doesn’t get too far down the standpipe or sink.

• Maintain Height: Your washer’s manual will specify the height at which the hose should be installed (usually 30–96 inches).

• Secure the Hose: Prevent the hose from slipping out of place with clamps.

8. Electrical or Control Board Problems

The washer may not advance to the drain cycle due to a malfunctioning control board or timer.

Quick Fix:

• Reset the Washer: Unplug the washer, turn it off, wait 5–10 minutes, and then turn it back on.

• Inspect for Damage: Check for burns or damage on the control board.

• Professional Repairs: If the board is bad, change it with the help of a technician.

If your Frigidaire washer isn’t draining, it’s most likely because of a problem with one of the most important Frigidaire washer parts. Keeping your washer in good repair and being sure it’s maintained regularly helps keep it clean and working fit. However, if the problem continues, it’s best to check with a pro to ensure more complicated issues such as a broken control board or timer.

I'm an independent blogger dedicated to sharing practical tips and insights on home appliances. My goal is to help readers enhance the performance and longevity of their kitchen equipment.