Directory Image
This website uses cookies to improve user experience. By using our website you consent to all cookies in accordance with our Privacy Policy.

Configuration the SerialGhost Premium!

Author: Jack Conner
by Jack Conner
Posted: May 19, 2020

The SerialGhost Premium Keylogger (SerialGhost Wi-Fi Premium) may be configured through the file CONFIG.TXT, placed in the flash drive root folder. Use any text editor to prepare such a configuration file, containing the following text:

Baudrate=9600Bits=8Parity=NoStopBits=1

Copy this file to the root folder in flash drive mode. The new configuration will be loaded on next power-up.

The following list presents the most common configuration options. All variable and value strings are case insensitive.

Baudrate sets the baud rate in bits per second of the monitored serial bus. Range is 300 bps to 115,200 bps. Default value is 9600.

Bits sets the number of bits per transfer of the monitored serial bus. Possible values are 5, 6, 7, 8. Default value is 8.

Parity sets the parity bit type of the monitored serial bus. Possible values are No, Even, Odd, Space, Mark. Default value is No.

StopBits sets the number of stop bits per transfer of the monitored serial bus. Possible values are 1, 1.5, 2. Default is 1.

Timestamping configures the built-in time- and date-stamping module. Allowed values are Yes (timestamping enable) and No (timestamping disabled). Default is Yes.

TimestampInterval sets the interval of serial bus inactivity in seconds, that will trigger a new time-stamp being logged. Range is 1 second to 9999 seconds. Default value is 10.

DisableLogging allows to disable logging. Allowed values are Yes (logging disabled) and No (logging enabled). Default value is No.

LogMode sets the logging mode. Possible values are Bin (data is logged as binary data), Hex (data is logged as hexadecimal numbers), Dec (data is logged as decimal numbers). Default value is Bin.

Separator sets the separator character between data values in logging mode Dec/Hex. Possible values are None, Space, Comma, Tab, Newline. Default is Space.

LogStream configures which serial streams are to be logged. Possible values are Both (both RX and TX get logged), Rx (only Rx is logged), Tx (only Tx is logged). Default is Both. If the mode is set to Both, the [1] and [2] markers will be used to differentiate between streams.

StreamMarkers configures if the markers designating the active stream ([1] and [2]) are logged or not. Allowed values are Yes (markers enabled) and No (markers disabled). Default value is Yes.

UsbMode allows to switching between flash drive mode and Virtual COM mode. Allowed values are Flash (flash drive mode) and Com (Virtual COM mode). Default value is Flash. A full list of parameters is available in section Configuration files. Configuration:

The SerialGhost Premium and SerialGhost Wi-Fi Premium can be configured and operated entirely from KL Tools. Launch the application, select the device model, and choose to configure your device. The application will first display a serial bus configuration dialog, and then a time configuration dialog. If changing the default password, memorize or note the new values, otherwise access to the internal memory will not be possible. If unsure about a certain configuration option, leave the default value.

Finally, a network configuration dialog will be shown. Enter standard static IP, gateway and DNS data, or select the Auto-IP option to use DHCP.

The SerialGhost Wi-Fi Premium can connect to a wireless LAN network. In such case enter the data allowing the logger to connect to the WLAN Access Point:

WLAN Access Point ID (SSID) WLAN encryption type WLAN encryption password

Remember, that these strings are case-sensitive.

To receive E-mail reports containing serial data, supply your E-mail address. You may adjust the reporting interval and report size.

When finished, make sure the device is connected as in record mode. KL Tools will automatically create configuration files (CONFIG.TXT, TIME.TXT), prompt for enabling flash drive mode, and copy the files to the loggers flash drive.

For more please do visit: https://www.keelog.com/

About the Author

I am Jack, Working as a Marketing Manager at keelog which gives Usb keylogger and Keylogger to monitor your employees, Children or any other person.

Rate this Article
Leave a Comment
Author Thumbnail
I Agree:
Comment 
Pictures
Author: Jack Conner

Jack Conner

Member since: Jan 08, 2019
Published articles: 43

Related Articles